Millermatic 180 230 Volt - 907312

Millermatic 180 MIG Welder (230 Volt)

You don't have to be an expert to get great welds with the Millermatic 180 MIG welder. This compact, portable package delivers a maximum output of 180 amps and is ideal for maintenance, auto body and fabrication projects. The Millermatice 180 is easy to use and move.

Applications/Processes

• Light Industrial Applications
• Light Fabrication
• Maintenance and Repair
• Auto Body
• Farm and Ranch
• Home
• Flux Cored (FCAW) (gas and self-shielded)
• MIG (GMAW)
  
  Features:
• NEW! Smooth-Start patent-pending technology provides a smooth, spatterfree start. It’s the best-starting machine in the small MIG machine category. No pop gun starts and no spatter to clean up.
• Infinite Voltage Control with Manual On/Off Wire Feed Speed Tracking provides a broader operating range with finer control by automatically increasing or decreasing wire feed speed when voltage is adjusted (unit shipped with wire feed speed tracking set to “off”).
• NEW! More output. Semiautomatic constant voltage wire welding package is capable of welding 24 gauge up to 5/16 in (0.8 – 7.9 mm) mild steel.
• Durable cast aluminum feedhead incorporates dual-groove quick-change drive roll and spring-loaded tension arm with calibrated tension knob all designed to make set up easier and faster.
• Miller’s exclusive “Tip Saver” short circuit protection shuts down output when tip is shorted to the work. Extends contact tip life and protects internal components from damage. Trigger reset permits quick reset at torch rather than unit.
• Easy access to output studs provides convenient polarity changeover when changing from solid or flux cored wires.
• Thermal overload protection shuts down unit and activates over temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools.
• Standard built-in solid-state contactor circuit makes wire electrically “cold” until trigger is pulled, making the unit safer. It’s also easier to position torch to work before starting weld.
• Self-resetting motor protection circuit eliminates the need to find and replace fuses.
• Uses 4 or 8 in (102 or 203 mm) spools and can be set up to weld with wire sizes .024 – .035 in (0.6 – 0.9 mm) mild/ stainless steel and .030–.045 in (0.8–1.2 mm) flux cored.
• Add the Spoolmate 3035 spool gun and SGA spool gun adapter for welding with .030 –.035 in (0.8 – 0.9 mm) aluminum wire on 14 gauge to 1/4 in material.
  
  Comes Complete with:
• Power source
• 6 ft (1.8 m) power cord and plug
• 10 ft (3 m), M-10 MIG gun and cable assembly
• 10 ft (3 m) work cable and clamp
• Smith Argon and AR/CO2 mix regulator/flow gauge with hose
• Spool of Hobart .030 in (0.8 mm) solid wire
• Two contact tips for .024 in (0.6 mm) wire and two contact tips for .030 in (0.8 mm) wire
• Dual groove quick-change drive roll for .024 in (0.6 mm) or .030/.035 in (0.8/0.9 mm) wire
• Factory-installed gas solenoid valve
• Set-up and operation video
• Information/settings chart
  
  Quick Specs Millermatic 180
• Input Power Requires: 1-Phase Power, 230 V, 19.5 A, 60 Hz
• Rated Output: 135 A at 20 VDC, 30% Duty Cycle
• Output Power Range: 30 - 180 Amps
• Weight: 72 lb (32.7 kg)